Question: Should I Stain My Butcher Block Countertop?

Is there a food safe stain for Butcher block countertops?

Pure tung oil is a good choice for a food safe wood finish for your butcher block countertop or kitchen island.

It’s easy to apply, nontoxic and leaves a beautiful matte finish that fits into almost any home style.

There’s something special about wood butcher block countertops..

Does butcher block stain easily?

Con: Butcher-block is susceptible to scratches, dings, and stains. If you plan on chopping directly on your countertops, you’re going to end up marking things up a little (or a lot). That glass you dropped might just leave a dent, and the wine inside could settle into a stain. Pro: But they’re easily restored.

How do you maintain a butcher block?

Butcher Block Countertop Maintenance 101Clear the counters of all items and lightly sand them with a medium sandpaper block. … Wipe off all of the dust with a barely-damp rag.Warm the wax bottle under hot water for a few seconds, then squirt a line of wax around the counters.More items…

What kind of stain do you use on butcher block?

Hardwood Reflections Ebony gel stain is designed specifically for butcher block or other interior wood products that require a very high-end finish for an area of heavy use. Gel stains are very thick and provide a striking color when cured.

Is it safe to stain butcher block?

We don’t recommend using a stain on a butcher block counter top because the stain is most likely not food safe. The stain could seep out of the counter and into your food, causing the food to taste bad and possibly be toxic. Our Cutting Board Oil and Butcher Block Conditioner are better alternatives and are food safe.

What should I use to seal my wood countertop?

Apply coats of polyurethane to the countertop surface. A sealed surface makes the countertop easy to clean but is not recommended for cutting surfaces. Select a urethane that is FDA approved to ensure the substance is safe to be in contact with your food. Apply at least 3 coats to get a good, solid coating.

Is wood stain toxic after it dries?

Whenever the stain dries and its solvent evaporates, it will be releasing a volatile organic compound or VOC. This is the one that can contribute to air pollution and can also cause health problems. … The lesser the VOC, the better it is for you.

What is the best finish for Butcher block countertops?

Polyurethane for butcher block countertops. Polyurethane is a liquid coating that dries into a plastic film and is excellent for sealing the countertop, but then there’s a layer of plastic between you and your pretty new wood.

Can you use polyurethane on butcher block?

Polyurethane for butcher block countertops. Polyurethane is a liquid coating that dries into a plastic film and is excellent for sealing the countertop, but then there’s a layer of plastic between you and your pretty new wood.

What is the best finish for a wood countertop?

Waterlox® is a tung oil-based permanent finish that will stand up to hard daily use. It is ideal for countertops, island tops, bar tops, and table tops. It’s tough, hard, and food safe. Additionally, this finish is waterproof, heat- and stain-resistant.

Is Minwax wood stain Food Safe?

According to finishing expert Bob Flexner, all finishes are food-safe once they have cured. Polyurethane varnish does not present any known hazard. However, no finish is food safe until it has fully cured. The rule of thumb for full curing is 30 days at room temperature (65- to 75- degrees F).

Should I seal my butcher block countertop?

There are a variety of options for permanently sealing and waterproofing butcher block wood countertops, commonly used in kitchens. … A penetrating sealer soaks into a substrate such as wood, concrete or stone, and it seals the pores from the inside. Once it cures, moisture is not able to penetrate the surface.

What do you seal butcher block with?

Sealing Butcher Block Countertops with Mineral Oil To seal butcher block with mineral oil, you simply apply the mineral oil generously, let it soak in, and wipe off the excess. You need to do it fairly regularly at first but then only about once a month after you’ve gotten through several applications.

How do you seal a butcher block countertop after staining?

Also stain your butcher block if you’ve had your counters for several years and the current finish is looking worn or faded. Sand the wood before staining, then select a wood stain and apply at least 2 coats. Then finish the stain with a coat of tung oil or other food-safe sealant.

How do you waterproof wood countertops?

Rub the linseed oil into the wood while moving the wiping cloth in the direction of the wood grain. Make sure the cloth is thoroughly saturated with the oil as it is rubbed into the wood, until the entire top and edge surfaces have been saturated. Wipe off any leftover oil that has pooled on the surface.